Rendering fat is much easier than you might expect. All you need is a good stock pot, some heat-proof utensils and bowls, and… some fat to render. It’s a great way to use “waste” products and turn them into either tasty stirfry or, better yet, homemade soap.
To get the fat, you can take the trimmings off briskets or other store-bought pork and beef, especially handy if you plan to can the meat later.
In this case, because I intend to turn pork fat into soap, I purchased 20 pounds of pork fat from the local Richardson Farms in Temple, Texas, who raise pastured (aka happy) pigs. I believe in supporting local farmers as much as possible, and I also think you get a much higher quality product when the animals do not suffer throughout their lives.
Before I began I needed to make sure the fat was as cold as possible but still manageable. Cold fat is much easier to chop, whether you do it by hand or run it through a meat grinder. I chose to ice it down in a large cooler; you could also freeze it, though be warned that a 20 fat ice cube will be difficult to cut later.
Because I have no grinder, I chopped it up into cubes, roughly (and I do mean roughly) about 1/2 inch on a side. This is an imprecise science, so just do your best. The smaller the pieces, the more surface area will be exposed, making the rendering process faster and arguably you’ll get more fat in the long run.
I was able to fit about 2/3 of the bag into two stock pots, each with about 1/2 cup of water added to the bottom.
I turned the heat on high until the water came to a boil and began to break down the fat, and then I reduced the heat to medium. Slowly the solid chunks of fat melted into a light golden liquid, and cracklins, the solid meaty bits, floated to the top.
It can take a couple hours to get all of the fat melted down. Eventually I ended up with two pots of liquid fat. From there, I had to (carefully!) strain out the solids from the liquid fat. I used a metal strainer lined with a folded flour sack cotton tea towel. You can also use coffee filters, multiple layers of cheesecloth, or a very fine mesh strainer. Just be sure that everything is heat-safe, as the fat is a lot hotter than boiling water and will melt most plastics (we won’t go there right now…).
Once the fat is strained, you can pour it into mason jars or other heat-proof containers while it’s still hot. Once it cools, if you did everything right it will become snow white in color, and in the fridge (where you should store it to keep it from going rancid) it will get rather firm in texture as well.
In my first round of rendering this batch, I accidentally had the heat on a bit too high and it reached the fat’s smoke point. I immediately removed the fat from the fire, but it unfortunately gave the lard a bit of a light brown tone, and may affect the tast. While this would possibly be unacceptable for cooking lard, I’m not going to waste it and will still use it for soap.
Surviving the Modern World 
great article jackie! i had been wondering about this very topic today and here it is! perfect!
Let me know how your own rendering experiments go!
great article jackie! i had been wondering about this very topic today and here it is! perfect!
Let me know how your own rendering experiments go!
Hi,
Great article!! I have 2 questions for you.
1)…the ‘cracklins” …..would that be like pork rinds that you used to get in the store in chip bags?
2) do you have a recipe for the soap you make from this.
oops…3 questions!!
2) are you just doing pork, for lard or are you doing beef for something too?
Thank you,
Helen
🙂
Thanks!
I suppose the cracklins are like pork rinds, though what I’ve made have been denser and greasier. I think I’d probably bake them and dry them out further before I’d eat them… but I haven’t tried that yet.
I’ve rendered both pork fat and beef fat, and have used soap made from both. The “brisket soap” was actually quite nice. I guess I’m partial to pork/lard for a variety of reasons, and it’s easier to come by, but really the two fats are both useful in much the same way.
And about soap – I’m going to be making another batch in a day or two, and will write up a post about that, with some photos.
Thanks for the reply. I will watch for the post!!
Helen
🙂
Hi,
Great article!! I have 2 questions for you.
1)…the ‘cracklins” …..would that be like pork rinds that you used to get in the store in chip bags?
2) do you have a recipe for the soap you make from this.
oops…3 questions!!
2) are you just doing pork, for lard or are you doing beef for something too?
Thank you,
Helen
🙂
Thanks!
I suppose the cracklins are like pork rinds, though what I’ve made have been denser and greasier. I think I’d probably bake them and dry them out further before I’d eat them… but I haven’t tried that yet.
I’ve rendered both pork fat and beef fat, and have used soap made from both. The “brisket soap” was actually quite nice. I guess I’m partial to pork/lard for a variety of reasons, and it’s easier to come by, but really the two fats are both useful in much the same way.
And about soap – I’m going to be making another batch in a day or two, and will write up a post about that, with some photos.
Thanks for the reply. I will watch for the post!!
Helen
🙂
I have rendered pork fat and at 40 outside temperature it is still liquid although it is just beginning to turn white. I once rendered pork fat and it had a high moisture content which was not good for making pastry dough and the soap making process was not as successful. Do you have the proportions of fat (before melting) to lye? Thank you.
Hi Bernadette!
You can read about my soapmaking technique here:
https://survivingthemodernworld.com/2012/making-homemade-piggie-soap/
In particular, there’s a link to the spreadsheet I use, which will do all the calculations of fat-water-lye for you (with allowances for different kinds of fats and superfatting!): http://www.millersoap.com/worksheet.html
I have rendered pork fat and at 40 outside temperature it is still liquid although it is just beginning to turn white. I once rendered pork fat and it had a high moisture content which was not good for making pastry dough and the soap making process was not as successful. Do you have the proportions of fat (before melting) to lye? Thank you.
Hi Bernadette!
You can read about my soapmaking technique here:
https://survivingthemodernworld.com/2012/making-homemade-piggie-soap/
In particular, there’s a link to the spreadsheet I use, which will do all the calculations of fat-water-lye for you (with allowances for different kinds of fats and superfatting!): http://www.millersoap.com/worksheet.html